RP2018

Battery Installation

1. To get started, remove the keyhole cover and insert one of your backup keys into the keyhole at the front of the safe. Push key in and rotate the key 30 degrees clockwise (RIGHT) to open the safe.
2. Locate and use the screwdriver to remove the battery compartment cover screw. Take the battery pack and insert 4 AAA alkaline batteries (not included) into the pack matching the polarity (+/-) indicated. NOTE: New batteries cannot be used together with old batteries.
3. First connect the front of the battery pack to two springs at the front of the battery compartment. Then push the back of the battery pack into the battery compartment.
4. When the batteries are inserted correctly, the keypad and fingerprint sensor will light up once with one beep. Place the battery cover and you are now ready to program your safe.

NOTE: Please pay attention to the battery pack installation sequence to avoid the incorrect installation which will render the device unusable.

Low Battery Warning

• The batteries need to be replaced when the fingerprint sensor lights up ROSE PINK and the keypad flashes BLUE 10 times with 10 beeps during electronic unlock.
• A built-in USB Type-C port on the front of the safe can be used when the batteries are depleted without the keys. This port is for emergency use only, not for long-term use.
• You can simply plug a USB Type-C cable (not included) into the port to electronically unlock the safe as normal. It cannot be used for charging.

IMPORTANT:

• Do not place or store the backup keys inside the safe at any time.
• Use 4 NEW AAA Alkaline batteries. New batteries can not be used together with old batteries.
• Mixing batteries may cause the device to become unusable.
• The safe locks automatically when the lid is fully closed.

 Master Code Programming

TIP: Code Requirements

• Programming a new code will overwrite your previous code.
• Your code can be a minimum of 4 and a maximum of 6 digits.
• Two keys cannot be pressed simultaneously

1. Enter default code 1-2-3-4-5-6 to open your safe.
2. With the safe open, press the Program Button once (2-3 seconds), the keypad will light up BLUE once with 1 beep. 
3. When the backlit remains BLUE, enter your NEW master code (4-6 digits).
4. Press the Program Button once and release it, the keypad will light up BLUE 2 times with the double beeps. This tone confirms that the password has been reset.
5. Now test the code. If you made a mistake, the keypad will flash RED 5 times with 5 beeps, and the new code does not work, simply start over from step 2.

Fingerprint Registering

1. With the safe open, press the Program Button once (2-3 seconds), the keypad will light up BLUE once with one beep.
2. When the backlit remains BLUE, place your finger on the fingerprint sensor for the 1st of six scans. Make sure your finger covers the sensor completely. Remove your finger after the keypad lights up BLUE once with 1 beep. You will repeat this process until the keypad lights up BLUE 2 times and fingerprint sensor lights up BLUE, with 2 beeps.
3. Now your fingerprint has been successfully registered.
4. Test your fingerprint. If your registered fingerprint is unsuccessful, the new fingerprint will not work. You must repeat the above steps to re-register your fingerprints.

NOTE:

• Make small adjustments to the position of your finger each time to ensure that the every angle of fingerprint can be scanned. While fingerprint sensor is scanning, you shouldn't move your finger around.
• You cannot register more than 20 fingerprints. If the keypad lights up RED 10 times with 10 beeps when you register your fingerprints, it means the fingerprint storage capacity is full.

Helpful Programming Tips:

1. Place your finger on the center of the sensor (this allows the sensor to read where most of the fingerprint detail is located).
2. Adjust your finger slightly between scans for increased accuracy.
3. Excessive moisture, lotion, or dirt will affect your fingerprint and may cause inaccurate sensor reading.
4. If you are experiencing difficulty, try different fingers. Each finger is unique, and some fingers such as your thumb, contain more readable information than others.
5. To increase your success rate, please register the same fingerprint multiple times.

Registered Fingerprints Deleting

1. Press and hold the Program Button. The keypad will light up BLUE once with 1 beep.
2. Keep holding the Program Button until the keypad lights up BLUE 2 times with 2 beeps.
3. Now all previously registered fingerprints are erased.

Lock-Down System

• If you enter the wrong code or unregistered fingerprints, the keypad will light up RED 5 times with 5 beeps.
• If the wrong code or unregistered fingerprint is entered 5 consecutive times, the safe will go into a lock-down mode for 5 minutes. After 5 minutes, the safe will automatically resume normal operation.
• During this time the keypad will keep flashing RED, the keypad and fingerprint sensor will be temporarily disabled. The safe can still be opened using the backup keys override.

Mute Mode Setting

To mute the audible sound of the electronics, press the Mute Button once (1-2 seconds), the keypad will light up BLUE 2 times. To unmute the mode, press the Mute Button once (1-2 seconds), the keypad will light up BLUE 2 times with 2 beeps.

Securing Your Safe

Mounting Screws Using

• Before installing the safe, make sure there is enough room for the lid to open properly.
• If the safe is mounted vertically with the door facing upwards, the safe will not open completely due to the weight of the safe. The door opens downwards or to the side when the safe is mounted vertically.

1. Place the safe on a flat surface where you want to mount it.
2. Mark the drill holes with a pencil and drill pilot holes.
3. Position the safe and insert screws through the safe into the pilot holes. Tighten the screws.

Security Cable Using

1.  Loop the security cable around a secured object.
2. Run the end of the cable through the eyelet on the other end and pull tightly around the object.
3. Insert the end of the security cable into the fully enclosed cable mount inside your safe.
4. Make sure the safe closes with the cable secured in the cable mount.